Technical Vocational Education and Training (TVET) Programme :

Electrical Maintenance and Management System

Training Duration : 4 months Classroom + 3 Months OJT (Inclusive of Core Abilities)
Course Fee : Fully sponsored by NCIA (Northern Corridor Implementation Authority)

Programme Certification

Certification will be provided to participants by KISMEC and Sijil Kecekepan Kemahiran (SKK) by CIDB.

Course Overview

This programme is aimed at producing workforce with competent in electrical maintenance and management to the industry, who are highly knowledge and competent, capable of complementing and supporting the comprehensive needs of the manufacturing industries plants and commercial building.

Participants will also be exposed with how to reduce equipment downtime, improve overall efficiency and safety, and fix problems that they have been unable to solve on their own.

Course content

  1. Basic of electrical maintenance and management
    • 1.1. Electricity Supply Act. 199O & Electricity Supply Regulation 1994
    • 1.2. Energy Commission Act 2OO1
    • 1.3. Electricity Supply Act. (Amendment) 2OO1
    • 1.4. Malaysia Standard Code of Practice for Electrical Installation of Building (MS IEC 60364)
    • 1.5. IEE Regulation – 16 th Edition
    • 1.6. Act and Safety Rules
  2. First Aid Treatment
  3. Safety and Health
    • 3.1. Workplace Electrical Safety
    • 3.2. Occupational Safety & Health Management
  4. Domestic and Industrial Power Supply
  5. Electrical installations & maintenance (Domestics & Industry)
  6. Technical Drawing
  7. Electric machines in buildings
  8. Maintenance & troubleshooting of Fire alarm system by BOMBA
  9. Motor Starter Control & Three Phase Industrial Motor
  10. Electrical testing & measurement method
  11. Electrical switchboards in buildings (MSB)
  12. Operating & Maintenance Air Conditioning system
  13. Electrical servicing and maintaining, troubleshooting works
  14. Consumer Installation
  15. Low voltage electrical lines in buildings and public equipment
  16. Underground lines to buildings and public equipment
  17. Introduction to electricity for energy management
  18. Approach & Benefit of Energy Management
  19. Energy-minded preventive maintenance management
  20. Use management tools to monitor and control energy costs
  21. Energy Management policies & organizational structure
  22. Electrical Radar
  23. Safety of Measurement Tester Equipment
  24. CIDB Green Card Course
  25. Calibrations – Primary & Secondary Injection Test Training by Certified contractor
  26. Green Technology – Solar & Wind turbine System

Learning Outcome

Participants will be able to:

    1. Comply with workplace Energy Commission Act (Suruhanjaya Tenaga) i.e. Malaysia Standard Code of Practice for Electrical Installation of Building (MSIEC 60364)
    2. Comply with workplace Electrical Safety (DOSH) standard i.e. LOTO, AESP, MSDC, Hazard, Risk Management
    3. Perform Electrical servicing and maintaining, troubleshooting works as per CIDB requirement
    4. Perform Maintenance & troubleshooting of fire alarm system as per BOMBA requirement
    5. Operate, Service and Calibrate of Electrical switchboards in buildings (Main Switch Board – MSB)

Entry Requirement

  1. Warganegara Malaysia
  2. Age not more than 35 years
  3. Fresh graduates with a Diploma holders in electrical & electronics / SKM Level 3 Electrical.

For more information please call: 04-441 4619 (En. Afif) or email: career@kismec.org.my

Front End Semiconductor Manufacturing Technology

Training Duration : 3 months Classroom + 6 Months OJT (Inclusive of Core Abilities)
Course Fee : Fully sponsored by NCIA (Northern Corridor Implementation Authority)

Programme Certification

Certification will be provided to participants by KISMEC and Silterra.

Course Overview

This course will cover all the front end process required in semiconductor process manufacturing.

Course content

  1. Manufacturing Topic (Training Methodology – Theory + Quizzes)
  2. Process Class
  3. QA
  4. FE Semiconductor Manufacturing Facility-Electrical
  5. FE Semiconductor Manufacturing Facility-Mechanical
  6. FE Semiconductor Manufacturing Facility-Chemical
  7. FE Semiconductor Manufacturing Facility-Gas
  8. FE Semiconductor Manufacturing Facility-Water
  9. FE Semiconductor Manufacturing Facility-Ultra Pure Water (UPW)
  10. FE Semiconductor Manufacturing Facility-Waste
  11. FE Semiconductor Manufacturing Facility-Instrument & Control
  12. FE Semiconductor Manufacturing Facility-Scheduled Waste
  13. FE Semiconductor Manufacturing Facility-Site Service

Learning Outcome

To produce competence manpower in:

    1. Photo Process
    2. Etch Process
    3. Diffusion Process
    4. Implant Process
    5. Thin Film Process
    6. CMP Process

Entry Requirement

  1. Warganegara Malaysia
  2. Age not more than 35 years
  3. Fresh graduates with a Diploma Holders in IT, Electronic, Mechanical or any related engineering subjects.

For more information please call: 04-441 4619 (En. Afif) or email: career@kismec.org.my

Opto-Semiconductor Manufacturing Technology

Training Duration : 4 months Classroom + 8 Months OJT (Inclusive of Core Abilities)
Course Fee : Fully sponsored by NCIA (Northern Corridor Implementation Authority)

Programme Certification

Certification will be provided to participants by KISMEC and Silterra.

Course Overview

This course will cover all the fundamentals manufacturing processes in the opto-semiconductor industry.

Course content

  • Module 1 : Core Module
    1. Chemical Handling Chemicals & Gases Plumbing & Fittings
    2. Soldering & Welding
    3. Robotic Operations
    4. Equipment Troubleshooting Methodologies
    5. Abatement System Training
    6. Equipment Operation
    7. Analytical Thinking
  • Module 2 : Mechanical
    1. Industrial Motor Application
    2. Vacuum Technology, Pumps Application
    3. Valves Application & Operation
    4. Electro Pneumatic Application
  • Module 3 : Electronic and Electrical
    1. RF System Application
    2. General Induction Sensor Technology and Temperature Controller
    3. Waferfab Process Introduction
    4. Electronics & Electrical Diagram
    5. Programmable Logic Controller

Learning Outcome

At the end of this training, participants will be able to learn and practice on

    1. Chemical handling chemicals, gases plumbing & fittings
    2. Mechanical Application & Operation in Opto-Semiconductor Manufacturing
    3. Electronic and Electrical related to Opto-Semiconductor Manufacturing

Entry Requirement

  1. Warganegara Malaysia
  2. Age not more than 35 years
  3. Fresh graduates with a Diploma Holders in IT, Electronic, Mechanical or any related engineering subjects.

For more information please call: 04-441 4619 (En. Afif) or email: career@kismec.org.my

Machining

Training Duration : 3 months Classroom + 6 Months OJT (Inclusive of Core Abilities)
Course Fee : Fully sponsored by NCIA (Northern Corridor Implementation Authority)

Programme Certification

Certification by KISMEC and FANUC (Fuji Automatic Numerical Control)

Course Overview

Machinists use machine tools such as lathes and milling machines to produce precision metal parts. They use their understanding of materials and skills with machine tools to plan and execute operations needed to produce machined products withprecise specification.

In KISMEC, our machining program provides the training in basic machine manufacturing processes. Participants will get exposure in technical drafting; develop skills in Computer Aided Design (CAD) and Computer Numerical Control (CNC) programming for Lathe & Milling. Possible employment opportunities include:

    1. Machine Tool Operator
    2. Machinist
    3. Mold Maker
    4. Shop Manager
    5. Tool and Die Maker

Course content

  1. Basic Technical Drawing
  2. General, Dimension & Tolerance
  3. CNC Turning simulator
  4. CNC Milling simulator
  5. CNC Turning Operation
  6. CNC Milling Operation
  7. Basic Essential Solid Works /CAD

Learning Outcome

Participants are capable to

    1. Define and develop basic engineering drawing
    2. Construct simple plane diagram using familiarized command in CAD
    3. Build parametric sheet metal models of parts and assemblies
    4. Understand basic CNC programming functions with CNC machine tool.

Entry Requirement

  1. Warganegara Malaysia
  2. Age not more than 35 years
  3. Fresh graduates with a SKM Level 3 / Diploma Holders in Engineering preferably Mechanical field.

For more information please call: 04-441 4619 (En. Afif) or email:career@kismec.org.my

PCB Design For Industry

Training Duration : 3 months Classroom + 6 Months OJT (Inclusive of Core Abilities)
Course Fee : Fully sponsored by NCIA (Northern Corridor Implementation Authority)

Programme Certification

Certification will be provided to participants by KISMEC

Course Overview

The program is carefully designed to bridge the gap between the current addressable talent supplies with the solar manufacturing skills.

Equipping learner with industry niche skills, the learning programs offered in this programme also equip graduates with on-demand skills and knowledge to be competent in the manufacturing environment.

This consequently reduces the dependency to hire foreign experts.

Course content

  1. FMEA (Failure Mode Effect Analysis)
  2. Employability Skills
  3. Technical Report Writing
  4. Workplace Communication
  5. Wiring and Soldering Technique
  6. Schematic Entry
  7. Component Library
  8. PCB Design Technology and Fabrication
  9. Introduction to ESD and EOS

Learning Outcome

The PCB Design Program’s curriculum gives students the diverse skills needed for employment and growth success in the PCB Design field. The PCB Design program will produce high skill workforce in create and design the pcb follow the IPC standard. They will become as an assistant engineer for RND department in electronic factory.

Entry Requirement

  1. Warganegara Malaysia
  2. Age not more than 35 years
  3. Fresh graduates with a SKM Level 3 / Diploma Holders in Electronic.

For more information please call: 04-441 4619 (En. Afif) or email: career@kismec.org.my

Robotic and Automation

Training Duration : 6 months Classroom + 6 Months OJT (Inclusive of Core Abilities)
Course Fee : Fully sponsored by NCIA (Northern Corridor Implementation Authority)

Programme Certification

Certification will be provided to participants by FESTO

Course Overview

Robots are being used worldwide in industries for various automated processes with minimal or reduced human intervention and even some processes have been completely automated. The integration of robotic system in industrial automation will increase quality due to the fact it could be operated with high precision. In addition, robotic system will save labor cost and meet production requirement in the long run.

To cater for human capital development in Industrial Automation program, KISMEC has developed courses to provide Malaysians with skills in the installation, troubleshooting and maintenance of a Robotic & Automation System.

The industry in Malaysia demands talent for the following :

    1. Welding Robot Application
    2. Material Handling Robot
    3. Assembly Automation Robot

Course content

  • Module 1 : Pneumatics
    1. Safety
    2. ISO Symbol and Drawing
    3. Pneumatic Air Generation
    4. Pneumatic Component
  • Module 2 : Advance Pneumatics
    1. Design Methodology
    2. Pneumatics Equiment Maintenance
    3. Circuit Design for Pneumatics
    4. Troubleshooting of Pneumatics System
    5. Basic Pneumatics Application in Industry
  • Module 3 : Electropneumatics
    1. Safety
    2. Basic Electric
    3. Components of Electropneumatics
    4. Structure of Electropneumatics
    5. Design of Electropneumatics Circuit
    6. Maintenance of Electropneumatics
    7. Troubleshooting of Pneumatics System
  • Module 4 : PLC Siemens
    1. Safety working with PLC
    2. Digital electronics
    3. PLC common structure
    4. PLC Circuit wiring
    5. Read and write PLC ladder
    6. Constructing PLC ladder
    7. Siemens PLC structure
    8. Siemens PLC instruction and Application
    9. Siemens PLC wiring
    10. Working with Block diagram
    11. Simatic S7 software
    12. Trouble shooting of Siemens PLC
    13. Maintenance of Siemens PLC
  • Module 5 : Hydraulics
    1. Safety in Hydraulics
    2. System generation in hydraulic system
    3. Component identification
    4. ISO symbol and standards
  • Module 6 : Advance Hydraulics
    1. Design Methodology for Hydraulics System
    2. Circuit Design Hydraulic System
    3. Maintenance of Hydraulic System
    4. Trouble shooting of Hydraulics System
    5. Electro Hydraulics
    6. Components of Electro Hydraulics System
    7. Structure of Hydraulic System
    8. Design of Electro Hydraulic System
    9. Maintenance of Electro Hydraulic System
    10. Trouble shooting of Electro Hydraulics System
  • Module 7 : Robotics
    1. Safety Working with Robots
    2. General Robotic system structure
    3. Robotic system structure
    4. Instruction application of Mitsubishi Robot
    5. Programming method
    6. Robotic
    7. Maintenance of Robot
    8. Trouble shooting of Robot

Learning Outcome

  1. Participants are competent in engineering software such as Electrical CAD, Siemens Step7 and OMRON CX1.
  2. Participants are able to do SCADA and HMI programming for control system.
  3. Participants are able to integrate the learning in polytechnics / universities with problem solving capabilities on automation controller, 3 phase system, hydraulics, pneumatics, and equipment networking.

Entry Requirement

  1. Warganegara Malaysia
  2. Age not more than 35 years
  3. Fresh graduates with a SKM Level 3/Diploma Holders in Electrical, Electronics, Mechanical, Mechatronic

For more information please call: 04-441 4619 (En. Afif) or email: career@kismec.org.my

Semiconductor Chip Testing Technology

Training Duration : 3 months Classroom + 6 Months OJT (Inclusive of Core Abilities)
Course Fee : Fully sponsored by NCIA (Northern Corridor Implementation Authority)

Programme Certification

Certification will be provided to participants by KISMEC and industry.

Course Overview

A basic knowledge of semiconductor physics and devices and of IC processing is needed for quite a number of functions, from IC technology engineers to test and product engineers and IC designers. This course is an introduction course and focuses on the IC fabrication process. It suitable for those want to become manufacturing or facilities technician in semiconductor manufacturing industries

Course content

  1. FMEA (Failure Mode Effect Analysis)
  2. Technical Report Writing
  3. Project Management
  4. Workplace Communication
  5. Employability Skills
  6. Introduction to ESD & EOS
  7. Introduction to PCB & SMT
  8. Introduction to Semiconductor IC Packaging/Assembly process
  9. Introduction to Semiconductor Manufacturing
  10. Fundamentals of LSI test
  11. Introduction to Test Engineering

Learning Outcome

Once the participants have completed the course, they will acquire:

    1. A basic knowledge of semiconductor physics and devices
    2. A basic knowledge of process steps in IC technology
    3. A basic knowledge of MOS IC processing
    4. Some knowledge of bipolar IC processing
    5. A basic knowledge of electrical process characterization and monitoring
    6. A basic insight in the relation between the semiconductor technology and the behavior of the devices.

Entry Requirement

  1. Warganegara Malaysia
  2. Age not more than 35 years
  3. Fresh graduates with a Diploma Holders in IT, Electronic, Mechanical or related engineering subjects.

For more information please call: 04-441 4619 (En. Afif) or email: career@kismec.org.my

Solar PV Industry

Training Duration : 3 months Classroom + 6 Months OJT (Inclusive of Core Abilities)
Course Fee : Fully sponsored by NCIA (Northern Corridor Implementation Authority)

Programme Certification

Certification by KISMEC and Sustainable Energy Development Authority Malaysia (SEDA Malaysia)

Course Overview

In Malaysia, solar power is expected to contribute to a minimum of 220 Megawatt in 2020 from 65 MW in 2015 under the National Renewable Energy Policy target. In fact, Economic Transformation Program (ETP) Entry Point Project 10 (EPP10) has laid down plan to build solar power capacity under Oil and Gas Sector to enhance energy independence, fulfill green agenda, increase energy security, increase employment and act as a catalyst for local solar manufacturing and Foreign Direct Investment (FDI). Labor and skills required to install solar system are expected to increase rapidly as government is encouraging solar energy installed at home and office with the introduced Feed-In Tariffs (FIT) to generate passive income.

To cater for human capital development in solar related program, SEDA has developed courses to provide Malaysians with skills in the designing, installation, andm maintenance of a Grid Connected Photovoltaic (GCPV) System. In fact, SEDA has the authority to ensure that only competent person is allowed to perform solar related work and ensure safety is followed as per Malaysian Standards.

Course content

SEDA Malaysia – Grid-Connected Solar Photovoltaic (PV) Systems Installer and Maintenance Training Course.

  • Module 1: Occupational Safety and Health Practice
    1. To prepare guideline on Occupational Safety and Health Act
    2. To familiarize on guideline for Occupational Safety and Health Act (practical)
    3. Types of common hazard at workplace
    4. Identification of hazard that could happen (practical)
    5. Recording procedure and documentation
    6. Checking list and hazard safety record(practical)
  • Module 2: Introduction to Solar Eelectricity
    1. Explanation of basic principle of electricity
    2. Explanation of basic principle of solar photovoltaic (PV)
    3. Explanation of principle of Balance of System (BOS) component and system operation
    4. Interpretation of Electrical drawing
  • Module 3: Preparation of System Installation
    1. Preparation of system component
    2. Identification of location
    3. Measurement of orientation and tilt angle
    4. Inspection of system installation
  • Module 4: System Device and Electrical System Installation
    1. Mounting of Inverter
    2. Mounting of DC combiner box / AC distribution box
    3. Installation of PV module on rooftop and ground
    4. Cabling of PV module system
    5. Cabling of inverter
    6. Layout plan of schematic diagram
    7. Implementation of DC Combiner and AC Distribution Box
    8. Implementation of Earthing system
    9. Installation of lightning protection
  • Module 5: Corrective Maintenance
    1. Inspection procedure
    2. Identification of fault
    3. Checking of schematic diagram
    4. Inspection of system integrity and power output
    5. Replacement of faulty component
    6. Verification of power output

Learning Outcome

  1. Participants are competent with SEDA requirement for installation work.
  2. Participants are familiar with Solar PV manufacturing process.
  3. Participants are able to integrate the learning in manufacturing process with solar installation work.

Entry Requirement

  1. Warganegara Malaysia
  2. Age not more than 35 years
  3. Fresh graduates with a SKM Level 3 / Diploma Holders in Technical and Engineering fields

For more information please call: 04-441 4619 (En. Afif) or email: career@kismec.org.my

Future Workers Training (FWT)Programme :

Automotive Assembly Operation

Programme Duration : 10 months (3 months at KISMEC + 7 months OJT)
Programme Code : TP-022-B
Course Fee : Fully sponsored by Perbadanan Tabung Pembangunan Kemahiran (PTPK)

Certification

  • Certification by KISMEC and MAI (Malaysia Automotive Institute) will be provided to participants who have successfully completed the programme

Course Overview

  • This module course is designed to expose participants to the principles of Automotive Assembly Operations covering Body Assembly, Painting and Final Assembly operations. It covers issues production scheduling, shop floor control, parts supply system, inventory control, budgetary control and also computerized manufacturing system such as Manufacturing Requirement Planning (MRP), and Enterprise Resources Planning (ERP). It also introduces the basic lean concept which is part of the world class automotive manufacturing system.

Course content

  1. Objectives and elements of Production Planning and Control
  2. Master Production Scheduling and Shop Floor Control (MPS and SFC)
  3. Bills of Materials and Materials Requirement Planning (BOM and MRP)
  4. Introduction to Cost Control – budgetary planning and control
  5. Manufacturing Engineering techniques – Layout, Process Flow/Charts, Materials Handling and Automation
  6. Logistics and Supply Chain Management in Automotive Assembly Operations
  7. Just in time and Lean Manufacturing
  8. Introduction to Product Design and Development

Benefit/Career Opportunity

  1. Understand basic overview of developing a new vehicle and outline of all phases and approval points of the product design & development processes
  2. Analyse key selected tools and techniques that are used to ensure the scope, timing and budget elements are managed along with setting the quality targets
  3. Understand the Original Equipment Manufacturers (OEM) roles, various types of suppliers, individuals that perform the product development tasks and how they are managed to ensure compliance to the programs scope, time, budget and quality targets required for the vehicles targeted to a specific market

Entry Requirement

  1. Warganegara Malaysia
  2. Age not more than 35 years
  3. Fresh graduates with a diploma in management or technical.

For Information or questions please call :
Automotive Department : 04-441 4619      ext. : 123
Mr. Zul : zulfauzi@kismec.org.my
Mrs. Syakirin : nursyakirin@kismec.org.my

Design Of Automation Equipment Programme

Programme Duration : 12 months (6 months at KISMEC + 6 months OJT)
Programme Code : MC-1211-B
Course Fee : Fully sponsored by Perbadanan Tabung Pembangunan Kemahiran (PTPK)

Certification

  • Certification by KISMEC

Course Overview

  • This course will provide students with the required knowledge for the design, installation, operation and maintenance of automation equipment used in industries. Industrial Automation is used especially in high end factories for various control processes with minimal or reduced human intervention. Various automation topics such as PLC, hydraulic, pneumatic and control system are covered to develop students with relevant skills and talents for high end factory requirement.

Course content

  1. Programmable Logic Control (PLC) system hardware
  2. Programmable Logic Control (PLC) system programming
  3. Industrial Mechanical & Electrical diagram
  4. Advance Hydraulic and Electro hydraulic system
  5. Advance Pneumatic and Electro Pneumatics
  6. Development and Maintenance of control system
  7. System trouble shooting

Benefit/Career Opportunity

  • After completing this course, students will be able work at Sales & Service Engineer, Design & Development and Maintenance technician

Entry Requirement

  1. Warganegara Malaysia
  2. Age not more than 35 years
  3. Fresh graduates with a diploma in Mechatronics, Electrical, Electronics, Mechanical, & Civil Engineering

For Information or questions please call :
Automation Department : 04-403 3978 (KISMEC Kulim)
Mr. Mahadzir : mahadzir72@gmail.com

Electrical Maintenance and Management

Programme Duration : 6 months ( 3 months at KISMEC + 3 months OJT )
Programme Code : EE-73-B
Course Fee : Fully sponsored by Perbadanan Tabung Pembangunan Kemahiran (PTPK)

Certification

  • Certificate in Fundamental of Energy Management – VDT Venture KISMEC

Course Overview

  • This course is aimed at producing unemployed graduates with competency in electrical maintenance and troubleshooting. This programme would equip participants with the required skills in electrical management, electrical measurements, electrical Act, safety law and energy management.

Course content

  1. Electrical Act / MS IEC 60364/ Safety Act
  2. Occupational safety
  3. Low Voltage & High Voltage Installation
  4. Motor Control
  5. Test & measuring equipment
  6. Three Phase Distribution Board Installation
  7. Street Lighting system
  8. Single & Three Phase wiring installation
  9. Under ground cable
  10. Solar of – grid system
  11. Air conditioning system
  12. Main Switch Board (MSB)
  13. Electrical Power management
  14. Energy conservation

Benefit/Career Opportunity

  • After completing this course, students will be able work at Electrical Engineer, Electrica Asst. Engineer, Electrical Supervisor and Electrical Contractor

Entry Requirement

  1. Warganegara Malaysia
  2. Age not more than 35 years
  3. Fresh graduates with a diploma in Electrical or Electronics field

For Information or questions please call :
Electrical Department : 04-441 4619        ext : 119
Mr. Suhaimi : suhaimi@kismec.org.my
Mrs. Amyilia : amylia@kismec.org.my

Industrial Plastic Product And Mould Design

Programme Duration : 10 months ( 4 months at KISMEC + 6 months OJT )
Programme Code : MC-1213-B
Course Fee : Fully sponsored by Perbadanan Tabung Pembangunan Kemahiran (PTPK)

Certification

  • Certification by by KISMEC and INVENTOR (Basic & Advance Tooling) will be provided to participants who have successfully completed the programme

Course Overview

  • This course provides participants a knowledge of plastics technology, mould design and mould making, plastic products quality and products testing.

Course content

  1. Safety at workplace
  2. Fundamentals of plastics technology
  3. Plastics technology process
  4. Plastics product and quality
  5. Plastic product testing
  6. Mould design and making
  7. Plastics product design using softwares
  8. Product prototyping

Benefit/Career Opportunity

  • After completing this course, students will be able work at many companies as a technician , engineer and designer in the relevant industries

Entry Requirement

  1. Warganegara Malaysia
  2. Age not more than 35 years
  3. Fresh graduates with a diploma in Mechanical, Polymer Technology, Tool & Die and others

For Information or questions please call :
Polymer Department : 04-441 4619        ext : 121
Mr. Aris Omar : aris@kismec.org.my
Ms. Nuraqilah : nuraqilah@kismec.org.my

Mobile Computing Application Developer - Android

Programme Duration : 7 months ( 4 months at KISMEC + 3 months OJT )
Programme Code : IT-120-C
Course Fee : Fully sponsored by Perbadanan Tabung Pembangunan Kemahiran (PTPK)

Certification

  • Certificate by KISMEC and University Utara Malaysia (UUM) will be provided to participants who have successfully completed the programme

Course Overview

  • This course is designed to quickly get you up to speed how to make Android apps for Android devices. This Android development training course will teach you the basis of the Android platform and the application lifecycle. You will be able to write simple GUI applications, use built-in widgets and components, work with the database to store data locally, and much more by the end of this Android training course.

Course content

  1. Basic Android Programming
  2. Problem Solving
  3. Java For Android
  4. Building User Interface
  5. Image Creation for Android
  6. Intent & Broadcast
  7. Sensors & Extend API
  8. Data persistence
  9. Internet,Webservices
  10. Location Based Services
  11. Application Distribution

Benefit/Career Opportunity

  1. Android training in a class setting will enable you to work with experts in the field who have actually created the types of apps and games that you aspire to create and make apps and games that the public are drawn to
  2. Can get a well-paying job at an IT-type company, or you will go it alone and develop games and apps to sell on the open market. Either way, the skills you’ve learned will translate into a living you can be proud of.

Entry Requirement

  1. Warganegara Malaysia
  2. Age not more than 35 years
  3. Fresh graduates with a diploma in Information Technology, Computer Sciences, Computer in Programming, Electronic Computer and related.

For Information or questions please call :
IT Department : 04-441 4619       ext : 129
Mrs. Hidayah : hidayah@kismec.org.my
Ms. Azwin : azwin@kismec.org.my

NDT Ultrasonic Testing Level 2 - CSWIP

Programme Duration : 7 months ( 3 months at KISMEC + 4 months OJT )
Programme Code : MC-1224-B
Course Fee : Fully sponsored by Perbadanan Tabung Pembangunan Kemahiran (PTPK)

Certification

  • Certification by KISMEC and CSWIP Ultrasonic Testing Level 2 ( 3.1 plate & 3.2 pipe) after completing the course and examination assessed by TWI Certification LTD and complying all CSWIP requirement

Course Overview

  • This course is designed to create an international certified professional in Non-Destructive Testing (NDT) by The Welding Institute (TWI). The skill and knowledge acquired in NDT principle and application will pave the way for the participants to meet the needs of both local and international industries in the oil and gas, aircraft, petrochemical, power generation environment and other related industries.

Course content

  1. Basic Principles of Sound
  2. Generation and Detection of Sound
  3. Behavior of Sound in a Material
  4. The Flaw Detector
  5. Use of Angled beam probes
  6. Welding Process
  7. Weld Defects
  8. Practical Exercises on Flawed Test Speciments
  9. Examination of Parent Plate
  10. Butt Welds
  11. Instruction Writing

Benefit/Career Opportunity

  1. Internationally recognized certificate and value added certificate for career advancement
  2. Smooth entry in the NDT community and related industries
  3. Highly competent NDT: UT personnel
  4. Knowledgeable applying relevant standards
  5. Skills needed in the international and local market

Entry Requirement

  1. Warganegara Malaysia
  2. Age not more than 35 years
  3. Fresh graduates with a diploma in Science Engineering or relevant discipline.
  4. Have an acceptable level of eyesight and do not suffer from colorblindness.

For Information or questions please call :
Oil & GasDepartment : 04-442 3271
Mr. Bazil : bazil@kismec.org.my
Ms. Syazana : syazana@kismec.org.my